649LikesTeam Associated B6 & B6D thread
06-07-2017, 10:46 AM - Wikipost
|
|||
|
|||
|
Welcome to the B6 Wiki!
Quick links to all the sections on the first page! Frequently asked questions - the most common questions you may have answered here! Aftermarket Parts - parts for the B6 and B6D Tech Tutorials- tuning guides, ball diff and shock building videos and tutorials How to's and build-specific posts Team Associated Laydown transmission conversion for B6D: Laydown conversion Instruction Manuals: B6: B6 Manual and setup sheets B6D: B6D Manual and setup sheets How to Sand and Seal carbon fiber: Sanding and sealing carbon fiber Sanding and sealing carbon fiber 2 Sanding and sealing carbon fiber 3 Sanding and sealing carbon fiber 4 Charts for Quick reference:         1) put inner bearing in hub 2) slide large shim over axle all the way up to the back of the axle 3) slide axle/bone into hub carrier 4) slide small shim onto axle through hub carrier 5) push outter bearing into hub carrier using that i'm able to put my normal male silverback gorilla wheel nut tightening job and there's no binding. in the pictures that come with the shims (the pic socket posted) it seems like they want you to slide both shims onto the axle before sliding the axle into the hub carrier and like i said, that doesn't work.  I've traditionally done the diff screw head on the left side (driver's side), but have since switched to the Right side (passenger side) regardless of transmission type (3 gear RM vs 3 gear MM and 4 gear MM). Kdub (Kurt Wenger, former AE designer) had this to say on the matter: I think I count as an authority on the matter. I always run my diff screw on the right side (when sitting "inside" the car). I take off the tire and pull the outer hinge pin to get to the adjustment screw.
The right rear is the way the AE manuals state (or used to state). It really shouldn't matter since you go around turns both left and right. 
|
07-11-2016, 11:52 AM
#1321
Tech Rookie
07-11-2016, 12:02 PM
#1322
Ordered mine last night, already shipped from Amain. Woot
07-11-2016, 12:25 PM
#1323
Do the standard buggy AE springs fit these new shocks?
This one?
http://site.petitrc.com/setup/associ...pringChart.pdf
This one?
http://site.petitrc.com/setup/associ...pringChart.pdf
07-11-2016, 12:39 PM
#1324
No. You'll need big bore springs.
I recommend Kyosho's or the Yokomo's.
I recommend Kyosho's or the Yokomo's.
07-11-2016, 01:29 PM
#1325
Just wondering if the turnbuckles and front axles fit from the b5? I have some Lunsford one I would like to use.
07-11-2016, 01:54 PM
#1328
Tech Regular
Turnbuckles will work. They're a millimeter or two different, but will work. The front axles are different.
07-11-2016, 02:49 PM
#1329
Tech Rookie
So Amain is sold out of RC10B6D....
07-11-2016, 03:03 PM
#1330
Just got my finished build video complete. Turned out pretty good with some RawSpeed wheels/tires and some access from Schelle:
https://www.youtube.com/watch?v=isZzOPQTVQg
https://www.youtube.com/watch?v=isZzOPQTVQg
07-11-2016, 03:37 PM
#1331
Just got my finished build video complete. Turned out pretty good with some RawSpeed wheels/tires and some access from Schelle:
https://www.youtube.com/watch?v=isZzOPQTVQg
https://www.youtube.com/watch?v=isZzOPQTVQg
Edit: You need to clock the motor forward.
07-11-2016, 03:44 PM
#1333
07-11-2016, 04:02 PM
#1335
Tech Apprentice
iTrader: (4)
LAPartshouse showing 4 in stock.
http://www.losipartshouse.com/ASC90001-p/asc90012.htm
Mine shipped today so I am good
http://www.losipartshouse.com/ASC90001-p/asc90012.htm
Mine shipped today so I am good