649LikesTeam Associated B6 & B6D thread
06-07-2017, 10:46 AM - Wikipost
|
|||
|
|||
|
Welcome to the B6 Wiki!
Quick links to all the sections on the first page! Frequently asked questions - the most common questions you may have answered here! Aftermarket Parts - parts for the B6 and B6D Tech Tutorials- tuning guides, ball diff and shock building videos and tutorials How to's and build-specific posts Team Associated Laydown transmission conversion for B6D: Laydown conversion Instruction Manuals: B6: B6 Manual and setup sheets B6D: B6D Manual and setup sheets How to Sand and Seal carbon fiber: Sanding and sealing carbon fiber Sanding and sealing carbon fiber 2 Sanding and sealing carbon fiber 3 Sanding and sealing carbon fiber 4 Charts for Quick reference:         1) put inner bearing in hub 2) slide large shim over axle all the way up to the back of the axle 3) slide axle/bone into hub carrier 4) slide small shim onto axle through hub carrier 5) push outter bearing into hub carrier using that i'm able to put my normal male silverback gorilla wheel nut tightening job and there's no binding. in the pictures that come with the shims (the pic socket posted) it seems like they want you to slide both shims onto the axle before sliding the axle into the hub carrier and like i said, that doesn't work.  I've traditionally done the diff screw head on the left side (driver's side), but have since switched to the Right side (passenger side) regardless of transmission type (3 gear RM vs 3 gear MM and 4 gear MM). Kdub (Kurt Wenger, former AE designer) had this to say on the matter: I think I count as an authority on the matter. I always run my diff screw on the right side (when sitting "inside" the car). I take off the tire and pull the outer hinge pin to get to the adjustment screw.
The right rear is the way the AE manuals state (or used to state). It really shouldn't matter since you go around turns both left and right. 
|
05-15-2016, 02:30 PM
#498
Tech Regular
Been watching the stock Nats OCRC Raceway the New B6 is doing well.
05-15-2016, 05:43 PM
#500
J Concepts Stock Nats at OCRC in Huntington Beach, CA
Expert Stock Buggy
1st Steven Hartson B6d with laydown tranny
2nd Casey Becica b5m with laydown WWHD tranny
3rd Kody Numedahl B6d with laydown tranny
Great results for AE. Casey is a privateer and led every lap except the last one. Pretty impressive.
http://www.liverc.com/view_result_fi...rand=463105143
Expert Stock Buggy
1st Steven Hartson B6d with laydown tranny
2nd Casey Becica b5m with laydown WWHD tranny
3rd Kody Numedahl B6d with laydown tranny
Great results for AE. Casey is a privateer and led every lap except the last one. Pretty impressive.
http://www.liverc.com/view_result_fi...rand=463105143
05-15-2016, 08:28 PM
#503
05-15-2016, 08:54 PM
#505
05-17-2016, 11:48 AM
#508
R/C Tech Elite Member
Full compatibility parts list can be found here
http://www.rcten.com/threads/b5-b6-b...ty-list.20367/
or
http://www.myrcbox.com/articles/team...tibility-list/
http://www.rcten.com/threads/b5-b6-b...ty-list.20367/
or
http://www.myrcbox.com/articles/team...tibility-list/
05-17-2016, 01:22 PM
#509
Full compatibility parts list can be found here
http://www.rcten.com/threads/b5-b6-b...ty-list.20367/
or
http://www.myrcbox.com/articles/team...tibility-list/
http://www.rcten.com/threads/b5-b6-b...ty-list.20367/
or
http://www.myrcbox.com/articles/team...tibility-list/
05-17-2016, 05:02 PM
#510
Finally the parts list!