R/C Tech Forums

Go Back   R/C Tech Forums > General Forums > Electric Off-Road

    Hide Wikipost
Old 12-26-2016, 07:51 PM   -   Wikipost
R/C Tech Forums Thread Wiki: Xray XB2 2WD Buggy Thread
Please read: This is a community-maintained wiki post containing the most important information from this thread. You may edit the Wiki once you have been a member for 90 days and have made 90 posts.
 
Last edit by: dgrobe2112
Instruction manuals: (C/O BentKa)

Xray XB2 Carpet Edition Instruction Manual
http://www.teamxray.com/xb2/2016/dow...ual_v2_low.pdf

Xray XB2 Dirt Edition Instruction Manual
http://www.teamxray.com/xb2/2016/dow...w.pdf?update=2

BentKa: Carpet Edition 4 gear to 3 gear laydown conversion parts:
  • Gearbox #323014
  • Motorplate #324012
  • 36T idler gear #324236
  • Brace for waterfall #324031


Socket: Bodies Available:

Xray has two OEM bodies, the .75mm and the .50mm light weight:
light weight: https://www.amainhobbies.com/xray-xb...329701/p492942

OEM .75mm: https://www.amainhobbies.com/xray-0....329700/p477762

Also, I've fitted the yz2 body, both the light and regular fit fine, just make your own cut lines:
https://www.amainhobbies.com/yokomo-...z2-101/p417674


[i] J Concepts S2 Body [i]


Penguin Racing makes a high grip body that fits the DE and CE:
http://www.ebay.com/itm/X-Ray-Xb2-Hi...oAAOSw1S9WewHV



Socket: Wheel fitment:

According to some, you'll require different offset rear hexes to use B5M wheels. According to my Hudy setup board, B5M wheels are the same offset. I measured the overall width of the car with XB2 wheels, and then again with B5M wheels, same measurement.

On the front, B5M wheels were 1.5mm wider. Xray offers hexes to reduce width -.75 on each side, or you could spend 3-5 minutes and sand your OEM hexes down .75mm.

edit by dgrobe2112
here are the hubs for losi and AE

for AE Front 365354 -0.75
for Losi rear 365358 +3.00 (4 stripe)
for AE rear 365359 +3.75 (5 stripe)



Socket: Flex and the XB2:

Flex screws are as follows:

Plastic bulkhead between motor and waterfall. Can remove screw in chassis, or remove bulkhead altogether.

Waterfall has 4 screws, can remove the inner two or outer two. IIRC, removing the inner two provides more flex, and thus more bite.

Removing the battery brace. This gives a tremendous amount of flex on the middle of the car, and can sometimes be inconsistent. I do this for outdoor racing on low bite. I like the feel over the 4 gear in 17.5 racing, since the 4 gear will take some snap away off the corner.

Rear C block - has inner and outer screws. I haven't played with this, as it's a crucial pivot point of the car.

Medium arms and towers -> I don't believe the carpet car has the rear medium tower available, however the DE DOES have an optional hard part. I think the hard parts are more consistent, especially when it gets hot (90+ degrees F). However, the medium parts do NOT break unless you're severely talented. They also don't wear out.



Socket: Avid/Schelle Slipper mod:

Credit to WillS, Matt Trimmings, and myself for figuring this out months ago.

Parts you'll need:

B5M V2 3gear compatible top shaft.
TKO Special 5x13x5 bear OR 5x13x6 bearing Either can work. This replaces the spur side bearing on the top shaft.
5mm shims, same shims used in 1/8th scale clutch bells. Look for protek .1mm and .2mm kit.
Avid or Schelle b5m top shaft kit, with spur gears of your choosing. (DE can't handle a 69, the CE can)

Shimming: You'll need to install the bearing in the front portion of the removable piece for the shaft. Make sure the bearing is pushed all the way in. With the TKO bearing, you'll need to shim approximately 1.4mm on the front side of the top shaft. Roughly .3-.5mm with the other bearing. This is a "feel" and tolerance setting. I urge you to watch videos about setting clutch bell play in 1/8th scale to get an idea of what yield you want for end play. Too tight, it'll eat bearings.

Outside of trans case: Use Avid/Schelle top shaft spacer plus .2mm shim to offset slipper from motor plate perfectly. Install slipper as instructed, and use Avid/Schelle spring and XB2 slipper nut.

- NEW - Schelle now sells Xb2 Topshafts. They include a spacer, so no need for shims in gearbox, and comes with the smaller bearing. Both methods work.

Socket: Yokomo Differential or MIP pucks:

Credit to: WillS for figuring out pucks, and as well fitting the Losi 22 diff with the same mods.

Parts needed: Yokomo Bmax2 or YZ2 complete diff OR Mip PUCKS outdrives
Xb2 diff gear
Bmax2 V3 Worlds rear dog bones, or Bmax 2 pucks dog bones
You'll use XB2 axles, and will require no other mods for the axles or dog bones.
You'll need .2mm outdrive/diff shims. Shim approximately .5mm on each side of the diff, behind the bearings. The top portion of the transmission is what "sets" the diff in place, not the bottom half. A little play back and forth is fine, the stock diff has some play from the factory.

dgrobe2112: CE to DE conversion:
along with the parts needed.. you MUST have these following hardware, or it wont work

https://www.teamxray.com/xb2/2016/do...conversion.pdf

(3) XRAY 902340 M3x40 button head screws. these are the screws that mount the motor mount to the tranny
(4) XRAY 903322 M3x22 counter sunk screws. these are for the rear diff case, to mount to the chassis. i think i used some M3x18 and they worked ok.

Socket: Best method for setting up the XB2 ball diff:

The XB2 diff is stellar when setup correctly. The spring is too short and soft, allowing the diff to slip. You'll need to glue the rings to the outdrives with just a drop of CA, then add a 1mm shim between the spring and the outdrive. This preloads the spring and stops the diff from slipping so easily.

OR, you can run the AE diff spring, which is both slightly longer, and stiffer. The overwhelming issue is the stock spring allows the nut to bottom out on the outdrive before the diff is tight enough.

This shim:
https://www.amainhobbies.com/xray-al...a303122/p12070

This diff spring (don't need a shim, then.)

https://www.teamassociated.com/parts...thrust_spring/

Functional Aftermarket parts: (Not just bling!)

Servo Horn: (The B5M sized horns are too short to get full throw)
https://www.amainhobbies.com/protek-...800-bk/p273496


Socket: Exotek has a full suite of parts, some bling, some not. Here's a list (all fit DE and CE, unless otherwise noted):

Titanium front axles: http://www.exotekracing.com/xb2-titanium-front-axles-2/

Rear Hanger, HD (Adds 4 grams): http://www.exotekracing.com/xb2-rear...75-heavy-duty/

Brass C block, 18 grams added: http://www.exotekracing.com/xb2-rear...-brass-weight/

Alloy front camber mount: http://www.exotekracing.com/xb2-fron...er-mount-7075/

Carbon Fiber Chassis: http://www.exotekracing.com/xb2-carb...m-plate-2-5mm/

Alloy rear hubs:http://www.exotekracing.com/xb2-allo...ub-set-2-7075/

Alloy servo mounts, allow for use of LP servo:http://www.exotekracing.com/xb2-xb4-...-alloy-1-pair/

Titanium shock mounts: http://www.exotekracing.com/xb2-xb4-...shock-posts-2/

Slipper Eliminator: http://www.exotekracing.com/xb2-direct-spur-mount/
Xray eliminator is #324100

dgrobe2112: 2016-2017 new 3 gear laydown
Gearbox #323014
Motor plate #324012
36T idler gear #324236
Brace for waterfall #324031

dgrobe2112: Xray Spring Rate Conversion:
front C WHT
368174 2 str 0.65-0.85 3.71-4.85

358184 2 dot 0.65 3.71
368185 3 dot 0.72 4.11
368186 4 dot 0.80 4.57


Rear
368273 2 str 0.35-0.45 2.00-2.57

368284 1 Dot 0.35 2.00
368285 2 Dot 0.40 2.28
368286 3 Dot 0.45 2.57
368287 4 Dot 0.50 2.86

Print Wikipost

Like Tree41Likes
Reply
 
Thread Tools Search this Thread
Old 03-02-2016, 01:38 PM   #1711
Tech Elite
 
symmetricon's Avatar
 
Join Date: Jun 2009
Location: houston
Posts: 4,721
Trader Rating: 27 (100%+)
Default

Quote:
Originally Posted by Iketruman View Post
Just checked Amain, still has not shipped. Ordered on December 21st and I am a platinum member. Hope everyone is right!!
They arrived at RCAmerica yesterday and have begun shipping. If you ordered from amain it will probably take several more days to arrive there and to then be processed and shipped...
__________________
XRAY / RCAMERICA
JCONCEPTS
RCSHOX
Mikes Hobby Shop
symmetricon is offline   Reply With Quote
Old 03-02-2016, 02:08 PM   #1712
Tech Elite
 
Customworksking's Avatar
 
Join Date: Oct 2004
Location: Springfield ILLINOIS
Posts: 3,638
Trader Rating: 73 (100%+)
Default

Quote:
Originally Posted by celt View Post
Pictures dude...
By tonight I bet we see several pictures
__________________
Team Xray | RC America| Hudy |Jaco |AKA
Customworksking is offline   Reply With Quote
Old 03-02-2016, 03:05 PM   #1713
Tech Elite
 
symmetricon's Avatar
 
Join Date: Jun 2009
Location: houston
Posts: 4,721
Trader Rating: 27 (100%+)
Default

__________________
XRAY / RCAMERICA
JCONCEPTS
RCSHOX
Mikes Hobby Shop
symmetricon is offline   Reply With Quote
Old 03-02-2016, 03:06 PM   #1714
Regional Moderator
 
RobsRacin's Avatar
 
Join Date: Jul 2014
Location: CT
Posts: 878
Trader Rating: 13 (100%+)
Default

Quote:
Originally Posted by symmetricon View Post
Holy smokes!!!!
RobsRacin is offline   Reply With Quote
Old 03-02-2016, 03:11 PM   #1715
Super Moderator
 
Cpt.America's Avatar
R/C Tech Elite Subscriber
 
Join Date: Mar 2009
Location: Washington State
Posts: 11,081
Trader Rating: 52 (100%+)
Default

Quote:
Originally Posted by symmetricon View Post
son of a!
__________________
A big thanks to my sponsors:
- Fantom Racing - www.fantomracing.com -
- Fusion Graphix- www.fusiongraphix.com -
- RCSpecialties -
Cpt.America is offline   Reply With Quote
Old 03-02-2016, 03:28 PM   #1716
Boz
Tech Fanatic
 
Join Date: Sep 2004
Location: Australia
Posts: 969
Trader Rating: 23 (100%+)
Default

Quote:
Originally Posted by xrayracer1 View Post
I live in Australia.
I'll have a Dirt Kit from the Australian importer before you receive yours from Amain.
__________________
Chris Bozich
Xray XB8 XB4 XB2
Futaba 4PX and servo's
Powered by Nosram motors and FX engines.
Many thanks to HEI and Perth RC for their support over the years.
Boz is offline   Reply With Quote
Old 03-02-2016, 03:28 PM   #1717
Tech Elite
 
symmetricon's Avatar
 
Join Date: Jun 2009
Location: houston
Posts: 4,721
Trader Rating: 27 (100%+)
Default

I told ya, order from RCAMERICA...
__________________
XRAY / RCAMERICA
JCONCEPTS
RCSHOX
Mikes Hobby Shop
symmetricon is offline   Reply With Quote
Old 03-02-2016, 03:44 PM   #1718
Boz
Tech Fanatic
 
Join Date: Sep 2004
Location: Australia
Posts: 969
Trader Rating: 23 (100%+)
Default

I would be happy if I could build the diff so it worked.

My geared diff worked better on our dirt track. That is how bad I re-build ball diffs.
__________________
Chris Bozich
Xray XB8 XB4 XB2
Futaba 4PX and servo's
Powered by Nosram motors and FX engines.
Many thanks to HEI and Perth RC for their support over the years.
Boz is offline   Reply With Quote
Old 03-02-2016, 04:43 PM   #1719
Tech Master
 
xrayracer1's Avatar
 
Join Date: Feb 2013
Location: Under your bed.
Posts: 1,186
Trader Rating: 1 (100%+)
Default

Quote:
Originally Posted by Boz View Post
I'll have a Dirt Kit from the Australian importer before you receive yours from Amain.
Whatever
__________________
Gavin.

Converting nitro to electric is utter blasphemy.
xrayracer1 is offline   Reply With Quote
Old 03-02-2016, 05:28 PM   #1720
Boz
Tech Fanatic
 
Join Date: Sep 2004
Location: Australia
Posts: 969
Trader Rating: 23 (100%+)
Default

Quote:
Originally Posted by xrayracer1 View Post
Whatever
__________________
Chris Bozich
Xray XB8 XB4 XB2
Futaba 4PX and servo's
Powered by Nosram motors and FX engines.
Many thanks to HEI and Perth RC for their support over the years.
Boz is offline   Reply With Quote
Old 03-02-2016, 05:48 PM   #1721
Tech Fanatic
R/C Tech Elite Subscriber
 
Join Date: Jul 2003
Location: El Pueblo de Nuestra Señora La Reina de Los Ángeles del Río de Porciúncula, California, Unites States of America
Posts: 944
Trader Rating: 30 (100%+)
Default

nice tires
__________________
...............
lagcisco is offline   Reply With Quote
Old 03-02-2016, 05:52 PM   #1722
Tech Master
 
suby723's Avatar
 
Join Date: May 2011
Location: Spring Hill Tennessee
Posts: 1,377
Trader Rating: 21 (100%+)
Default

Quote:
Originally Posted by symmetricon View Post
I told ya, order from RCAMERICA...
Ya damn right! Rc America is the only way to go!
suby723 is offline   Reply With Quote
Old 03-02-2016, 06:19 PM   #1723
Tech Elite
 
JEFFs SC10's Avatar
 
Join Date: Sep 2010
Location: Orlandooooo, Fl
Posts: 3,866
Trader Rating: 14 (94%+)
Default

Dirt edition really means more suitable for clay correct?

or for outdoors?
__________________
XRAY T4 17' //CRC Gen X SE- 17.5 GT//Xray X12-17' GT12//Xray X12-18' 17.5
check out the new 12th scale GT class!
https://www.facebook.com/groups/148391312353349/
JEFFs SC10 is offline   Reply With Quote
Old 03-02-2016, 06:31 PM   #1724
Tech Elite
 
celt's Avatar
 
Join Date: Jan 2004
Location: /dev/null
Posts: 2,364
Trader Rating: 5 (100%+)
Default

Quote:
Originally Posted by JEFFs SC10 View Post
Dirt edition really means more suitable for clay correct?

or for outdoors?
Correct...medium to low traction surfaces.
__________________
"Soon they will get everything they deserve. This isn't about trite elitism, but the otherwise intellectual and educated classes refusing to think for themselves. I call it situational ignorance, and painfully intolerable."

Stan Garvin
celt is offline   Reply With Quote
Old 03-02-2016, 09:21 PM   #1725
Tech Elite
 
symmetricon's Avatar
 
Join Date: Jun 2009
Location: houston
Posts: 4,721
Trader Rating: 27 (100%+)
Default

The carpet edition for reference.
__________________
XRAY / RCAMERICA
JCONCEPTS
RCSHOX
Mikes Hobby Shop
symmetricon is offline   Reply With Quote
Reply



Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are Off



All times are GMT -7. It is currently 09:11 PM.


Powered By: vBulletin v3.9.2.1
Privacy Policy | Terms of Use | Advertise Content © 2001-2011 RCTech.net