R/C Tech Forums
Page 3 of 200
1
2
3
4
5
13
53
103
Last »
Show 40 post(s) from this thread on one page

R/C Tech Forums (https://www.rctech.net/forum/)
-   Electric Off-Road (https://www.rctech.net/forum/electric-off-road-4/)
-   -   Tekno RC EB48.3 Thread (https://www.rctech.net/forum/electric-off-road/882749-tekno-rc-eb48-3-thread.html)

Riflebuilder 07-02-2015 03:49 AM
Thanks, running a Savoy 1258TG in my 410.3, overall been happy. What should I run on the EB48.3? Running Tekin RX8 Gen 2, so it should handle power hungry servos.

kawi650 07-02-2015 05:07 AM
Originally Posted by Riflebuilder (Post 14077502)
Thanks, running a Savoy 1258TG in my 410.3, overall been happy. What should I run on the EB48.3? Running Tekin RX8 Gen 2, so it should handle power hungry servos.
There will be many recommendations on servos but I run the Savox 1268 in both my buggy and truggy and have been more than happy. The performance is great on 7.4V but only decent on 6V so crank up the BEC on that Tekin.

micrors4guy 07-02-2015 05:32 AM
Originally Posted by fizzy (Post 14077356)
I'm getting this as my first ebuggy I was wondering what are the essential spares/upgrades needed and if anyone can advise on a good 1/8 ESC/ motor combo as I've only ever ran electric 1/10 touring cars any advice/ help would be great
get the Tekno al. servo horn.that should really be the only upgrade you will need.

the tekin gen2 esc and 1900kv motor is used the most.

Riflebuilder 07-02-2015 12:14 PM
Ordered the Savox 1283SG for the buggy. I figured this would be the best for what I'm looking to do.

MX304 07-02-2015 12:21 PM
Originally Posted by Riflebuilder (Post 14078124)
Ordered the Savox 1283SG for the buggy. I figured this would be the best for what I'm looking to do.

That's what I have in my EB48.2. Works great!

Riflebuilder 07-02-2015 12:25 PM
Originally Posted by MX304 (Post 14078132)
That's what I have in my EB48.2. Works great!
Was hoping someone would say that!!

Riflebuilder 07-03-2015 04:42 AM
I'm getting my 48.3 at my local shop at retail pricing, but Amain will have them at $60 off. Figured I would help someone!!

Riflebuilder 07-03-2015 04:45 AM
Originally Posted by micrors4guy (Post 14077213)
Smc and promatch both have quality 4s packs at good prices.
Checked out SMC batteries. Price is half the Protek at Amain. The only problem is what connectors should I be running?? My 410.3 runs 4mm bullets and I would like to standardize them. From what I understand the SCT needs the best connectors as possible because of the amp draw while the 1/8 ebuggies can get by with less?? Any thoughts?

werner sline 07-03-2015 05:02 AM
any picture with the body ? can't wait to see this massiv front tower !!

Dan.J 07-03-2015 06:11 AM
Originally Posted by Riflebuilder (Post 14079048)
Checked out SMC batteries. Price is half the Protek at Amain. The only problem is what connectors should I be running?? My 410.3 runs 4mm bullets and I would like to standardize them. From what I understand the SCT needs the best connectors as possible because of the amp draw while the 1/8 ebuggies can get by with less?? Any thoughts?
Most run Deans on there buggies, I too have bullets on my 410.3 and yes there is ALOT of amp draw on a heavy 4wd SCT with a 2s setup.

murat61 07-03-2015 06:20 AM
Originally Posted by Riflebuilder (Post 14079048)
Checked out SMC batteries. Price is half the Protek at Amain. The only problem is what connectors should I be running?? My 410.3 runs 4mm bullets and I would like to standardize them. From what I understand the SCT needs the best connectors as possible because of the amp draw while the 1/8 ebuggies can get by with less?? Any thoughts?
550 size motors continuously generates maximum power around1000 watts while buggy motors reach around 1300 watts(guessing from neu motor chart). Since buggies use 4s lipo compared to 2s lipo in sct, amp draw will be significantly lower in theory.

Riflebuilder 07-03-2015 06:43 AM
So dean's should be good to go then?

MX304 07-03-2015 06:57 AM
Originally Posted by Riflebuilder (Post 14079163)
So dean's should be good to go then?
Yes, that will work fine.

Hoese37 07-03-2015 08:01 AM
Originally Posted by Riflebuilder (Post 14079048)
Checked out SMC batteries. Price is half the Protek at Amain. The only problem is what connectors should I be running?? My 410.3 runs 4mm bullets and I would like to standardize them. From what I understand the SCT needs the best connectors as possible because of the amp draw while the 1/8 ebuggies can get by with less?? Any thoughts?
Deans really work fine in either.

MOE 07-03-2015 08:08 AM
EC5 and forget about it.


All times are GMT -7. It is currently 02:27 AM.
Page 3 of 200
1
2
3
4
5
13
53
103
Last »
Show 40 post(s) from this thread on one page

Powered By: vBulletin v3.9.3.8
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.