Team Associated RC10 B5m Mid-Motor & Rear Motor Thread
|
|||
Tech Initiate
Hey Guys,
So I finished my first build. I am looking for tips on what to buy for the motor, speedo and servo.
I was told 17.5 to start with and upgrade from their.
Would a Tekin RS Gen2 Sensored Brushless ESC with a reedy 17.5 brushless work well together? Leaving room to upgrade motor in future to 8.5 or something?
Anyway, feel free to list off the parts you'd piece together or what you would do and Ill take a look at each.
Thanks!
So I finished my first build. I am looking for tips on what to buy for the motor, speedo and servo.
I was told 17.5 to start with and upgrade from their.
Would a Tekin RS Gen2 Sensored Brushless ESC with a reedy 17.5 brushless work well together? Leaving room to upgrade motor in future to 8.5 or something?
Anyway, feel free to list off the parts you'd piece together or what you would do and Ill take a look at each.
Thanks!
Last edited by edgetechNY; 05-28-2014 at 03:15 PM.
Tech Master
iTrader: (16)
HBRob I have the 1.6 and 1.7 tapered with the 32.5 weight oil all around, White and Green springs. I used that at JBRL at OCRC but now put the pucks in and top shaft, so about 35 grams lighter, thinking of going to 30 weight oil front and 27.5 rear, dropping spring rates by one setting front and back and tune from that point.
Next race is outdoor at CCR, never been but yesterday in Exeter car was bouncy, track had some rough bumps and getting ready for a rebuild but need to lighten up and absorb a little more.
Running stock class so helps to be close to 1500 grams.
Next race is outdoor at CCR, never been but yesterday in Exeter car was bouncy, track had some rough bumps and getting ready for a rebuild but need to lighten up and absorb a little more.
Running stock class so helps to be close to 1500 grams.
Last edited by Cridd; 05-28-2014 at 07:30 PM.
Tech Initiate
I bought all my Ti stuff and schelle slipper at amain for a good deal using this link to their coupon code here.
Tech Champion
iTrader: (22)
ran my car at 1680 outside and it was dialed. Pulling wheelies
Only 3rd time I've even run it and it was still setup for indoors
Super Soft Impacts rear M3 holeshot fronts.
Here's the track we were on. It grooved up nicely.
https://www.youtube.com/watch?v=O5LnXHqkrNc
Only 3rd time I've even run it and it was still setup for indoors
Super Soft Impacts rear M3 holeshot fronts.
Here's the track we were on. It grooved up nicely.
https://www.youtube.com/watch?v=O5LnXHqkrNc
Suspended
Hey Guys,
So I finished my first build. I am looking for tips on what to buy for the motor, speedo and servo.
I was told 17.5 to start with and upgrade from their.
Would a Tekin RS Gen2 Sensored Brushless ESC with a reedy 17.5 brushless work well together? Leaving room to upgrade motor in future to 8.5 or something?
Anyway, feel free to list off the parts you'd piece together or what you would do and Ill take a look at each.
Thanks!
So I finished my first build. I am looking for tips on what to buy for the motor, speedo and servo.
I was told 17.5 to start with and upgrade from their.
Would a Tekin RS Gen2 Sensored Brushless ESC with a reedy 17.5 brushless work well together? Leaving room to upgrade motor in future to 8.5 or something?
Anyway, feel free to list off the parts you'd piece together or what you would do and Ill take a look at each.
Thanks!
Tech Regular
iTrader: (27)
I have not had any issues yet because I don't even have the car together yet (been way too busy ), however, I have one of the first batches of B5s and first batches of axles and aluminum hexes. I also have Avid Bearings. I just want to make sure I am not going to have issues, but I guess I may have to wait until I drive it to find out.
I have not had any issues yet because I don't even have the car together yet (been way too busy ), however, I have one of the first batches of B5s and first batches of axles and aluminum hexes. I also have Avid Bearings. I just want to make sure I am not going to have issues, but I guess I may have to wait until I drive it to find out.
hey there wc I got my bodys off to the painter and Lunsford front axales and a fantom apex 17.5 for the b5 m kit love this buggy
What are some things i can do to make my b5 have better corner speed? It has no aftermarket parts and is set up to facory specs besides shocks and gullwing arms/tower. Please dont just tell me to buy a b5m because i have one.
Tech Initiate
Tech Initiate
Ok quick question for you guys. I have my B5 set for mod running a 8.5 and a rs gen 2.
What should I add to my B5 to make it a even better buggy? Its bone stock right now. Nothing has been changed its built by the manual and nothing has been adjusted. Just curious with the summer series coming up I would like to do better then last year...9th place isn't good enough for me this year!
What should I add to my B5 to make it a even better buggy? Its bone stock right now. Nothing has been changed its built by the manual and nothing has been adjusted. Just curious with the summer series coming up I would like to do better then last year...9th place isn't good enough for me this year!
Tech Lord
iTrader: (52)
Ok quick question for you guys. I have my B5 set for mod running a 8.5 and a rs gen 2.
What should I add to my B5 to make it a even better buggy? Its bone stock right now. Nothing has been changed its built by the manual and nothing has been adjusted. Just curious with the summer series coming up I would like to do better then last year...9th place isn't good enough for me this year!
What should I add to my B5 to make it a even better buggy? Its bone stock right now. Nothing has been changed its built by the manual and nothing has been adjusted. Just curious with the summer series coming up I would like to do better then last year...9th place isn't good enough for me this year!