48LikesHyper TT 4wd 1/10th Truggy Thread
11-15-2010, 03:54 PM
#721
yeah, i was considering that also... but i have about 10 pair of good sct wheels i run on my slash, so if i keep it 12mm, i will save money on tires....
11-15-2010, 05:22 PM
#722
Hyper 10TT videos
11-15-2010, 06:17 PM
#724
The first one is new.. I just uploaded it. Not to long or good, but kills a couple minutes sittin at the computer.
11-15-2010, 06:43 PM
#725
ok so i read through some pages as i dont have the time to read through all 40+ pages there is a mod on the sc version to change from pivot ball to chub ill post the pic if nec. or refer to last page on barnstormers thread. the video posted is our maiden voyagethere is a lot of interest on our track. we race on a large track outside but yes its small inside.im the orange one that yes had a shaky start but got better. i left the stock diff setup and could get the rear to rotate but am weary on leaving grease in the diffs. so
1. any ideas on how to change to c-hub front as we all experienced isses of pillow balls coming loose on hubs as i guess since there getting hard to find this must be common
2.what diff fluid will give me same feel as stock as i drove tioffel's which did not rotate at all???
thanks all help is appreciated as our track will have 5-6 more next week
love it fun as hell although i do see how we need to make it more durable with rear hubs n top plate..lol
1. any ideas on how to change to c-hub front as we all experienced isses of pillow balls coming loose on hubs as i guess since there getting hard to find this must be common
2.what diff fluid will give me same feel as stock as i drove tioffel's which did not rotate at all???
thanks all help is appreciated as our track will have 5-6 more next week
love it fun as hell although i do see how we need to make it more durable with rear hubs n top plate..lol
11-15-2010, 07:03 PM
#726
I just read in RC car action Chad Bradley uses the hyper pivot ball front suspension on his Jammin? so I am sure it works the other way as well.
11-15-2010, 07:12 PM
#727
11-15-2010, 07:39 PM
#728
Tech Apprentice
11-15-2010, 08:19 PM
#729
i would swap arms and stuff just to get the front knuckles of the scrt but its narrower than the tt
11-16-2010, 04:02 AM
#730
How much narrower is it? Can the difference be made up with a thicker wheel hex or a different offset wheel? Is the Jammin rear suspension interchangeable with the hyper TT?
I took a picture of the article from the mag, hope you can read it.
I took a picture of the article from the mag, hope you can read it.
11-16-2010, 08:09 AM
#731
How much narrower is it? Can the difference be made up with a thicker wheel hex or a different offset wheel? Is the Jammin rear suspension interchangeable with the hyper TT?
I took a picture of the article from the mag, hope you can read it.Attachment 667947
I took a picture of the article from the mag, hope you can read it.Attachment 667947
11-16-2010, 09:03 AM
#732
How much narrower is it? Can the difference be made up with a thicker wheel hex or a different offset wheel? Is the Jammin rear suspension interchangeable with the hyper TT?
I took a picture of the article from the mag, hope you can read it.Attachment 667947
I took a picture of the article from the mag, hope you can read it.Attachment 667947
11-16-2010, 05:45 PM
#735
what mods did you half to do to the tt to get them to fit?