AndyMoore

iTrader: (64)

Not a problem, I'll check on the other thing you asked about tomorrow and get back to you.

Stealth_RT, you should be able to get many weekends out of the tires then.

cpatel529

iTrader: (80)

I just put the Rulux spoked wheels on the front and rear of my BJ4 (non-worlds). Unfortunately, I am getting a lot of rubbing in the front and my wheels are not spinning properly. How can I move the wheels out so that they dont rub?

Chirag

MustGoFaster

iTrader: (1)

Remove the front BJ4 hexes and put the B44 front hexes on.
Part # 9750

AndyMoore

iTrader: (64)

Exactly correct.

RCBLUE

iTrader: (7)

Ya those are B44 front wheels not BJ4 front wheels. I just put the whole B44 CVA kit in my BJ4WE along with the B44 front arms and now I can run both wheels. It takes some very precise Dremel work for the a arms, but worth it.

cpatel529

iTrader: (80)

Wow today went poorly. It was my first race day with my non-worlds BJ4 and I broke before qualifiers. First I took out an arm and then I broke a steering knuckle. Unfortunately, I didnt have any with me and the shop didnt have any so I had to watch. I tried to use the B44 front C Hub and steering knuckle but I couldnt get the silver BJ4 CVD/driveshaft to fit properly. I read that they were backwards compatible but it didnt seem to work for me.

Anyone have a good starting point setup for the non-worlds BJ4 on a hard packed clay surface? I am running double D's all around with a 10.5.

Chirag

MOmo

iTrader: (2)

Chirag,

Hey, its MOMO from BigDads, the guy looking at your TC5.

I have a BJ4WE with a pretty good setup. are you running Friday? Greg, (RCBlue) has a BJ4 and is very knowledgable with setups, so is Max. I'll have to see what my schedule looks like, but I might pop down to Amain on Friday.

Shoot me a PM and ur #.


momo

AndyMoore

iTrader: (64)

More information:

http://www.rcsignup.com/tracks/displayEvent.cfm?ID=267

AndyMoore

iTrader: (64)

Open Practice Friday May 30 gates open at 10:00 AM -7:00PM
Saturday MAY 31 gates open at 7:00AM open practice untill 8:00AM
9:00 starts 3 ROUND QUALIFIERS
8 SEATS 2 BUMP-UP MAINS
Announcer Kenny Holmes

Over night parking of trailers is Ok. and always has been, we just can
Not sleep in the park, gates will get locked 11:00PM.
So we have a Days Inn close by that will give
Us rooms for $35- $39 a night....
Days Inn
2900 Int'l Speedway/I-95
I-95 & US 92 Exit 261B
Daytona Beach, FL 32124
Phone: 386-255-0541
Just Let them know that you are racing at East Coast R/C Club

This is a great price, cheaper then staying in the park. With the
price of generator fuel
Right now this may be more by June. A room for $35- $39 with a hot
shower
Sounds great I think.
If you have any questions please call Brad Pascale (845) 494- 1800

Minnow

iTrader: (11)

Does ANYONE sell JConcepts tires in Denver?? I am dying to get a pair of each of the Double Dee's and Goose Bumps for my T4 but I WANT THEM NOW!!! lol


Other then buying them off the website I was hoping I could just run and get some.

Kyosho_101

iTrader: (7)

Can any one tell me what type of battery configuration I will need for my BJ4WE as it will arrive in about 3 days just want to make sure I can get batteries before it arrives

cola

iTrader: (308)

You can get a MaxAmps 4400 or 6000 saddle pack for it. If you are going to use lipo's you will need batteries built in a saddle pack arrangement.

Kyosho_101

iTrader: (7)

So i guess if I use sub c's they also have to be sadle packs (we can't use lipo at sanctioned events yet)

J_P

Yes, three by three. Looking down at the car from the rear, towards the front. Put the black battery wire on the left front, outside. A six inch piece of wire from the inside right rear of the left pack. To the inside left rear of the right pack. And the red battery wire on the right front, outside.

sparksy

iTrader: (14)

Kyosho_101...

Mate I'm after some JConcept wheels and tires for 10th scale 4wd. Can't seem to find them local. If you can help me out could you send me a PM. Would rather work out a deal in Aust than order off the net.

Thanks mate.