*** CAPRICORN CO2 NITRO TOURER and HEAPS OF PARTS ***
#1
#### ONLY CAPRICORN CO2 NITRO TOURER LEFT ####
I have for sale here a Capricorn CO2 nitro tourer. The car has had very little use and is in good condition.
It comes with an Xray receiver box, Capricorn clutch, brass battery tray and alloy servo horns. There is a complete spare rear diff and an almost complete front diff, some used plastic spurs, spur clutch bell and shoes.
Nothing on the car needs replacing.
PRICE
Roller = $420 + postage
Roller and 2 x Savox low profile servos = $470 + postage
CAPRICORN CO2 PARTS
I also have the following parts which are all brand new in the packets.
Rear lower arm x 2
Front left steering knuckle x 1
Front right steering knuckle x 1
Front lower arm x 2
Front upper arm x 3
Spurs x 5
Kevlar pulley set x 1
1st gear pinion x 2
2nd gear pinion x 3
Rear upright x 2
CO2 rear upper arm set x 1
Front CVD kit x 1
Alloy down stop set x 1
Male and Female bladed sway bar set x 1
Tensioner holder small bearings x 1
Plastic uniball ends x 4
Front lower hinge pin set x 1
ALL PARTS SOLD!
PRICE
SOLD + postage
It comes with an Xray receiver box, Capricorn clutch, brass battery tray and alloy servo horns. There is a complete spare rear diff and an almost complete front diff, some used plastic spurs, spur clutch bell and shoes.
Nothing on the car needs replacing.
PRICE
Roller = $420 + postage
Roller and 2 x Savox low profile servos = $470 + postage
CAPRICORN CO2 PARTS
I also have the following parts which are all brand new in the packets.
Rear lower arm x 2
Front left steering knuckle x 1
Front right steering knuckle x 1
Front lower arm x 2
Front upper arm x 3
Spurs x 5
Kevlar pulley set x 1
1st gear pinion x 2
2nd gear pinion x 3
Rear upright x 2
CO2 rear upper arm set x 1
Front CVD kit x 1
Alloy down stop set x 1
Male and Female bladed sway bar set x 1
Tensioner holder small bearings x 1
Plastic uniball ends x 4
Front lower hinge pin set x 1
ALL PARTS SOLD!
PRICE
SOLD + postage
Last edited by CDS70; 10-05-2012 at 12:47 AM.
#2
Tech Fanatic
iTrader: (29)
I have for sale here a Capricorn CO2 nitro tourer. The car has had very little use and is in good condition.
It comes with an Xray receiver box, Capricorn clutch, brass battery tray and alloy servo horns. There is a complete spare rear diff and an almost complete front diff, some used plastic spurs, spur clutch bell and shoes.
Nothing on the car needs replacing.
PRICE
Roller = $420 + postage
Roller and 2 x Savox low profile servos = $470 + postage
CAPRICORN CO2 PARTS
I also have the following parts which are all brand new in the packets.
Rear lower arm x 2
Front left steering knuckle x 1
Front right steering knuckle x 1
Front lower arm x 2
Front upper arm x 3
Spurs x 5
Kevlar pulley set x 1
1st gear pinion x 2
2nd gear pinion x 3
Rear upright x 2
CO2 rear upper arm set x 1
Front CVD kit x 1
Alloy down stop set x 1
Male and Female bladed sway bar set x 1
Tensioner holder small bearings x 1
Plastic uniball ends x 4
Front lower hinge pin set x 1
The total retail price is around the $500 mark.
PRICE
$250 + postage
It comes with an Xray receiver box, Capricorn clutch, brass battery tray and alloy servo horns. There is a complete spare rear diff and an almost complete front diff, some used plastic spurs, spur clutch bell and shoes.
Nothing on the car needs replacing.
PRICE
Roller = $420 + postage
Roller and 2 x Savox low profile servos = $470 + postage
CAPRICORN CO2 PARTS
I also have the following parts which are all brand new in the packets.
Rear lower arm x 2
Front left steering knuckle x 1
Front right steering knuckle x 1
Front lower arm x 2
Front upper arm x 3
Spurs x 5
Kevlar pulley set x 1
1st gear pinion x 2
2nd gear pinion x 3
Rear upright x 2
CO2 rear upper arm set x 1
Front CVD kit x 1
Alloy down stop set x 1
Male and Female bladed sway bar set x 1
Tensioner holder small bearings x 1
Plastic uniball ends x 4
Front lower hinge pin set x 1
The total retail price is around the $500 mark.
PRICE
$250 + postage
#3
Chris YGPM
Cheers Darren
Cheers Darren
#4
Hahahahaha.... You seem to forget Brooksey that I owned an MTX5 at one stage and as a result I can't afford a decent camera because all my money went on trying to keep bloody spur gears up to it................... If you're interested in moving on those MTX5's of yours let me know and I can email you some better photos.
Jazza and Chris.....PM's replied sorry for the delay.
Regards
Chris
Jazza and Chris.....PM's replied sorry for the delay.
Regards
Chris
#5
PARTS SOLD
Last edited by CDS70; 10-04-2012 at 03:58 AM.
#6
CO2 remaining.................
#7
CO2 Sold - Pending payment - Thanks for all the interest.
Everything now sold.
Everything now sold.